Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 28800

Cone Part Number

 N/A 28880

Cup Part Number

 N/A 28820

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 28880-90011 28880-902A1

Dimensions

d - Bore

 N/A 9.7500 in247.650 mm

D - Cup Outer Diameter

 N/A 12 in304.8 mm

B - Cone Width

 N/A 0.875 in22.225 mm

C - Cup Width

 N/A 0.6250 in15.875 mm

T - Bearing Width

 N/A 0.8750 in22.225 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.520 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

 N/A 10.08 in256 mm

db - Cone Backface Backing Diameter

 N/A 10.16 in258 mm

Da - Cup Frontface Backing Diameter

 N/A 11.69 in296.93 mm

Db - Cup Backface Backing Diameter

 N/A 11.46 in291.08 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.12 in3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.03 in0.8 mm
a - Effective Center Location3 N/A 0.68 in17.3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 9170 lbf40800 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 35400 lbf157000 N

C0 - Static Radial Rating

 N/A 83900 lbf373000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 5100 lbf22700 N

Factors

K - Factor7 N/A 1.8
e - ISO Factor8 N/A 0.32
Y - ISO Factor9 N/A 1.85

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 807

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 572
Cg - Geometry Factor10 N/A 0.148
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.