Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 3100

Cone Part Number

 N/A 3191

Cup Part Number

 N/A 3129

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1 3/16 in30.163 mm

D - Cup Outer Diameter

 N/A 3 in76.2 mm

B - Cone Width

 N/A 1.1810 in29.997 mm

C - Cup Width

 N/A 0.9375 in23.813 mm

T - Bearing Width

 N/A 1.1876 in30.165 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 N/A 0.030 in0.76 mm

da - Cone Frontface Backing Diameter

 N/A 1.52 in38.5 mm

db - Cone Backface Backing Diameter

 N/A 1.75 in44.5 mm

Da - Cup Frontface Backing Diameter

 N/A 2.74 in69.10 mm

Db - Cup Backface Backing Diameter

 N/A 2.56 in65.02 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.06 in1.5 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.03 in0.8 mm
a - Effective Center Location3 N/A -0.4 in-10.2 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 5520 lbf24600 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 21300 lbf94800 N

C0 - Static Radial Rating

 N/A 22800 lbf102000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 3140 lbf14000 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 23.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 8.76
Cg - Geometry Factor10 N/A 0.0697
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.