Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 3300

Cone Part Number

 N/A 3386

Cup Part Number

 N/A 3329

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1 9/16 in39.688 mm

D - Cup Outer Diameter

 N/A 3.2187 in81.755 mm

B - Cone Width

 N/A 1.1965 in30.391 mm

C - Cup Width

 N/A 0.9375 in23.813 mm

T - Bearing Width

 N/A 1.1563 in29.370 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.03 in0.800 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 1.79 in45.5 mm

db - Cone Backface Backing Diameter

 N/A 1.83 in46.5 mm

Da - Cup Frontface Backing Diameter

 N/A 2.99 in75.90 mm

Db - Cup Backface Backing Diameter

 N/A 2.8 in71.12 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.07 in1.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.06 in1.5 mm
a - Effective Center Location3 N/A -0.43 in-10.9 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 6700 lbf29800 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 25800 lbf115000 N

C0 - Static Radial Rating

 N/A 29100 lbf129000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 3130 lbf13900 N

Factors

K - Factor7 N/A 2.14
e - ISO Factor8 N/A 0.27
Y - ISO Factor9 N/A 2.2

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 34.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 12.1
Cg - Geometry Factor10 N/A 0.0744
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.