Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 385

Cone Part Number

 N/A 385X

Cup Part Number

 N/A 383A

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 2.1654 in55.001 mm

D - Cup Outer Diameter

 N/A 3.937 in100 mm

B - Cone Width

 N/A 0.8640 in21.946 mm

C - Cup Width

 N/A 0.7018 in17.826 mm

T - Bearing Width

 N/A 0.8269 in21.003 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 N/A 0.08 in2.03 mm

da - Cone Frontface Backing Diameter

 N/A 2.4 in61 mm

db - Cone Backface Backing Diameter

 N/A 2.64 in67 mm

Da - Cup Frontface Backing Diameter

 N/A 3.68 in93.00 mm

Db - Cup Backface Backing Diameter

 N/A 3.50 in88.90 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.11 in2.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.03 in0.8 mm
a - Effective Center Location3 N/A -0.12 in-3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 6280 lbf28000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 24200 lbf108000 N

C0 - Static Radial Rating

 N/A 24100 lbf107000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 3810 lbf16900 N

Factors

K - Factor7 N/A 1.65
e - ISO Factor8 N/A 0.35
Y - ISO Factor9 N/A 1.69

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 42

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 15.7
Cg - Geometry Factor10 N/A 0.0859
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.