Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 39000

Cone Part Number

 N/A 39236

Cup Part Number

 N/A 39414X

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 2.3617 in59.987 mm

D - Cup Outer Diameter

 N/A 4.1339 in105.001 mm

B - Cone Width

 N/A 0.8661 in21.999 mm

C - Cup Width

 N/A 0.6299 in15.999 mm

T - Bearing Width

 N/A 0.8661 in21.999 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.09 in2.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.08 in2.03 mm

da - Cone Frontface Backing Diameter

 N/A 2.64 in67 mm

db - Cone Backface Backing Diameter

 N/A 2.8 in71 mm

Da - Cup Frontface Backing Diameter

 N/A 3.96 in100.10 mm

Db - Cup Backface Backing Diameter

 N/A 3.78 in96.01 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.12 in3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.05 in1.3 mm
a - Effective Center Location3 N/A -0.06 in-1.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 6680 lbf29700 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 25800 lbf115000 N

C0 - Static Radial Rating

 N/A 27000 lbf120000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 4440 lbf19700 N

Factors

K - Factor7 N/A 1.51
e - ISO Factor8 N/A 0.39
Y - ISO Factor9 N/A 1.55

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 51.7

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 19.5
Cg - Geometry Factor10 N/A 0.0947
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.