Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 46700

Cone Part Number

 N/A 46790A

Cup Part Number

 N/A 46720

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 6 1/2 in165.1 mm

D - Cup Outer Diameter

 N/A 8 7/8 in225.425 mm

B - Cone Width

 N/A 1.5625 in39.688 mm

C - Cup Width

 N/A 1.3125 in33.338 mm

T - Bearing Width

 N/A 1.6250 in41.275 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.310 in7.900 mm
r - Cup Backface "To Clear" Radius2 N/A 0.030 in0.762 mm

da - Cone Frontface Backing Diameter

 N/A 6.85 in174 mm

db - Cone Backface Backing Diameter

 N/A 7.44 in189 mm

Da - Cup Frontface Backing Diameter

 N/A 8.58 in217.932 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.12 in3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.13 in3.3 mm
a - Effective Center Location3 N/A 0.1 in2.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 17700 lbf78600 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 68200 lbf303000 N

C0 - Static Radial Rating

 N/A 143000 lbf635000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 11600 lbf51600 N

Factors

K - Factor7 N/A 1.52
e - ISO Factor8 N/A 0.38

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 572

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 154
Cg - Geometry Factor9 N/A 0.143
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.