Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 470000

Cone Part Number

 N/A 470975

Cup Part Number

 N/A 470132

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 7.5 in190.5 mm

D - Cup Outer Diameter

 N/A 13.2500 in336.550 mm

B - Cone Width

 N/A 3.3125 in84.138 mm

C - Cup Width

 N/A 2.5 in63.5 mm

T - Bearing Width

 N/A 3.2500 in82.550 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.190 in4.800 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 8.27 in210 mm

db - Cone Backface Backing Diameter

 N/A 8.54 in217 mm

Da - Cup Frontface Backing Diameter

 N/A 12.08 in306.83 mm

Db - Cup Backface Backing Diameter

 N/A 11.73 in297.94 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.09 in2.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.32 in8.1 mm
a - Effective Center Location3 N/A -0.55 in-14 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 55000 lbf245000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 212000 lbf944000 N

C0 - Static Radial Rating

 N/A 319000 lbf1420000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 34400 lbf153000 N

Factors

K - Factor7 N/A 1.6
e - ISO Factor8 N/A 0.37
Y - ISO Factor9 N/A 1.64
Cg - Geometry Factor10 N/A 0.127
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.