Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 48200

Cone Part Number

 N/A 48282

Cup Part Number

 N/A 48220

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 4.7500 in120.650 mm

D - Cup Outer Diameter

 N/A 7.1875 in182.563 mm

B - Cone Width

 N/A 1.5000 in38.100 mm

C - Cup Width

 N/A 1.3125 in33.338 mm

T - Bearing Width

 N/A 1.5625 in39.688 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 5.16 in131 mm

db - Cone Backface Backing Diameter

 N/A 5.39 in137 mm

Da - Cup Frontface Backing Diameter

 N/A 6.95 in176.53 mm

Db - Cup Backface Backing Diameter

 N/A 6.61 in167.89 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.15 in3.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.06 in1.5 mm
a - Effective Center Location3 N/A -0.22 in-5.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 15600 lbf69400 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 60200 lbf268000 N

C0 - Static Radial Rating

 N/A 111000 lbf493000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 8160 lbf36300 N

Factors

K - Factor7 N/A 1.91
e - ISO Factor8 N/A 0.31
Y - ISO Factor9 N/A 1.97

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 353

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 91.3
Cg - Geometry Factor10 N/A 0.114
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.