Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 535

Cone Part Number

 N/A 538

Cup Part Number

 N/A 533A

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 2.1649 in54.988 mm

D - Cup Outer Diameter

 N/A 4.0625 in103.188 mm

B - Cone Width

 N/A 1.4550 in36.957 mm

C - Cup Width

 N/A 1.1875 in30.163 mm

T - Bearing Width

 N/A 1.5000 in38.100 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.03 in0.800 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

 N/A 2.44 in62 mm

db - Cone Backface Backing Diameter

 N/A 2.48 in63 mm

Da - Cup Frontface Backing Diameter

 N/A 3.90 in99.06 mm

Db - Cup Backface Backing Diameter

 N/A 3.66 in92.96 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.07 in1.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.08 in2 mm
a - Effective Center Location3 N/A -0.48 in-12.2 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 10000 lbf44600 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 38700 lbf172000 N

C0 - Static Radial Rating

 N/A 46200 lbf206000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 5090 lbf22700 N

Factors

K - Factor7 N/A 1.97
e - ISO Factor8 N/A 0.3
Y - ISO Factor9 N/A 2.02

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 64.3

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 16.1
Cg - Geometry Factor10 N/A 0.0938
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.