Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 5300

Cone Part Number

 N/A 5395

Cup Part Number

 N/A 5320

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1 15/16 in49.213 mm

D - Cup Outer Diameter

 N/A 3.9843 in101.201 mm

B - Cone Width

 N/A 1.7510 in44.475 mm

C - Cup Width

 N/A 1.4375 in36.513 mm

T - Bearing Width

 N/A 1.7190 in43.663 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.560 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 2.36 in60 mm

db - Cone Backface Backing Diameter

 N/A 2.6 in66 mm

Da - Cup Frontface Backing Diameter

 N/A 3.82 in97.00 mm

Db - Cup Backface Backing Diameter

 N/A 3.46 in87.88 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.07 in1.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.08 in2 mm
a - Effective Center Location3 N/A -0.63 in-16 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 12400 lbf55000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 47700 lbf212000 N

C0 - Static Radial Rating

 N/A 60100 lbf267000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 6280 lbf27900 N

Factors

K - Factor7 N/A 1.97
e - ISO Factor8 N/A 0.3
Y - ISO Factor9 N/A 2.02

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 73.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 15.5
Cg - Geometry Factor10 N/A 0.0985
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.