Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 544000

Cone Part Number

 N/A 544090

Cup Part Number

 N/A 544116

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 544090-90403

Dimensions

d - Bore

 N/A 9 in228.600 mm

D - Cup Outer Diameter

 N/A 11.625 in295.275 mm

B - Cone Width

 N/A 1.2500 in31.750 mm

C - Cup Width

 N/A 0.9375 in23.813 mm

T - Bearing Width

 N/A 1.3125 in33.338 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.560 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 9.45 in240 mm

db - Cone Backface Backing Diameter

 N/A 9.61 in244 mm

Da - Cup Frontface Backing Diameter

 N/A 11.34 in288 mm

Db - Cup Backface Backing Diameter

 N/A 11.02 in279.91 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.15 in3.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.13 in3.3 mm
a - Effective Center Location3 N/A 0.62 in15.7 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 13900 lbf61600 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 53400 lbf238000 N

C0 - Static Radial Rating

 N/A 103000 lbf458000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 9530 lbf42400 N

Factors

K - Factor7 N/A 1.45
e - ISO Factor8 N/A 0.4
Y - ISO Factor9 N/A 1.49

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 648.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 279.2
Cg - Geometry Factor10 N/A 0.117
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.