Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 5500

Cone Part Number

 N/A 5562

Cup Part Number

 N/A 5535

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1 15/16 in49.213 mm

D - Cup Outer Diameter

 N/A 4 13/16 in122.238 mm

B - Cone Width

 N/A 1.7230 in43.764 mm

C - Cup Width

 N/A 1.4375 in36.513 mm

T - Bearing Width

 N/A 1.7188 in43.658 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.050 in1.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 2.48 in63 mm

db - Cone Backface Backing Diameter

 N/A 2.56 in65 mm

Da - Cup Frontface Backing Diameter

 N/A 4.60 in116.10 mm

Db - Cup Backface Backing Diameter

 N/A 4.17 in105.92 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.08 in2 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.07 in1.8 mm
a - Effective Center Location3 N/A -0.48 in-12.2 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 13800 lbf61300 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 53200 lbf237000 N

C0 - Static Radial Rating

 N/A 73500 lbf327000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 8460 lbf37600 N

Factors

K - Factor7 N/A 1.63
e - ISO Factor8 N/A 0.36
Y - ISO Factor9 N/A 1.67
Cg - Geometry Factor10 N/A 0.0825
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.