Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 565

Cone Part Number

 N/A 567X

Cup Part Number

 N/A 562

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 2.8750 in73.025 mm

D - Cup Outer Diameter

 N/A 5.1200 in130.048 mm

B - Cone Width

 N/A 1.4240 in36.170 mm

C - Cup Width

 N/A 1.1250 in28.575 mm

T - Bearing Width

 N/A 1.4376 in36.515 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.190 in4.800 mm
r - Cup Backface "To Clear" Radius2 N/A 0.030 in0.76 mm

da - Cone Frontface Backing Diameter

 N/A 3.19 in81 mm

db - Cone Backface Backing Diameter

 N/A 3.54 in90 mm

Da - Cup Frontface Backing Diameter

 N/A 4.80 in121.90 mm

Db - Cup Backface Backing Diameter

 N/A 4.57 in116.08 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.11 in2.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.1 in2.5 mm
a - Effective Center Location3 N/A -0.32 in-8.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 11400 lbf50900 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 44100 lbf196000 N

C0 - Static Radial Rating

 N/A 58900 lbf262000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 7130 lbf31700 N

Factors

K - Factor7 N/A 1.61
e - ISO Factor8 N/A 0.36
Y - ISO Factor9 N/A 1.65

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 101.3

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 24
Cg - Geometry Factor10 N/A 0.117
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.