Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 64000

Cone Part Number

 N/A 64452A

Cup Part Number

 N/A 64708

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 4.5266 in114.976 mm

D - Cup Outer Diameter

 N/A 7.0856 in179.974 mm

B - Cone Width

 N/A 1.625 in41.275 mm

C - Cup Width

 N/A 1.1875 in30.163 mm

T - Bearing Width

 N/A 1.6250 in41.275 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.350 in8.900 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 4.96 in125.9 mm

db - Cone Backface Backing Diameter

 N/A 5.63 in143 mm

Da - Cup Frontface Backing Diameter

 N/A 6.85 in173.00 mm

Db - Cup Backface Backing Diameter

 N/A 6.34 in161.04 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.11 in2.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.2 in5.1 mm
a - Effective Center Location3 N/A 0.05 in1.3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 16000 lbf71200 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 61800 lbf275000 N

C0 - Static Radial Rating

 N/A 94200 lbf419000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 14100 lbf62900 N

Factors

K - Factor7 N/A 1.13
e - ISO Factor8 N/A 0.52
Y - ISO Factor9 N/A 1.16

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 219

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 45.3
Cg - Geometry Factor10 N/A 0.115
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.