Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 6400

Cone Part Number

 N/A 6465

Cup Part Number

 N/A 6424

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 2 1/4 in57.15 mm

D - Cup Outer Diameter

 N/A 5.9055 in150 mm

B - Cone Width

 N/A 2.1350 in54.229 mm

C - Cup Width

 N/A 1.7717 in45.001 mm

T - Bearing Width

 N/A 2.1261 in54.003 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.270 in6.900 mm
r - Cup Backface "To Clear" Radius2 N/A 0.12 in3.05 mm

da - Cone Frontface Backing Diameter

 N/A 2.95 in75 mm

db - Cone Backface Backing Diameter

 N/A 3.46 in88 mm

Da - Cup Frontface Backing Diameter

 N/A 5.55 in140 mm

Db - Cup Backface Backing Diameter

 N/A 5.08 in129.03 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.06 in1.5 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.09 in2.3 mm
a - Effective Center Location3 N/A -0.59 in-15 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 24000 lbf107000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 92400 lbf411000 N

C0 - Static Radial Rating

 N/A 104000 lbf463000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 14800 lbf66000 N

Factors

K - Factor7 N/A 1.61
e - ISO Factor8 N/A 0.36
Y - ISO Factor9 N/A 1.66
Cg - Geometry Factor10 N/A 0.0931
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.