Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 6500

Cone Part Number

 N/A 6575

Cup Part Number

 N/A 6535W

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 3 in76.2 mm

D - Cup Outer Diameter

 N/A 6-3/8 in161.925 mm

B - Cone Width

 N/A 2.1693 in55.100 mm

C - Cup Width

 N/A 1.6875 in42.863 mm

T - Bearing Width

 N/A 2.1251 in53.978 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 3.62 in92 mm

db - Cone Backface Backing Diameter

 N/A 4.09 in104 mm

Da - Cup Frontface Backing Diameter

 N/A 6.08 in154.43 mm

Db - Cup Backface Backing Diameter

 N/A 5.55 in140.97 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.06 in1.5 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.15 in3.8 mm
a - Effective Center Location3 N/A -0.52 in-13.2 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 25600 lbf114000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 98800 lbf439000 N

C0 - Static Radial Rating

 N/A 118000 lbf523000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 17600 lbf78100 N

Factors

K - Factor7 N/A 1.46
e - ISO Factor8 N/A 0.4
Y - ISO Factor9 N/A 1.5

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 199

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 33.5
Cg - Geometry Factor10 N/A 0.1040
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.