Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 71000

Cone Part Number

 N/A 71433X

Cup Part Number

 N/A 71750

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 4.3307 in110 mm

D - Cup Outer Diameter

 N/A 7.5 in190.5 mm

B - Cone Width

 N/A 1.9375 in49.213 mm

C - Cup Width

 N/A 1.3750 in34.925 mm

T - Bearing Width

 N/A 1.8750 in47.625 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 4.8 in122 mm

db - Cone Backface Backing Diameter

 N/A 5.04 in128 mm

Da - Cup Frontface Backing Diameter

 N/A 7.17 in182.12 mm

Db - Cup Backface Backing Diameter

 N/A 6.73 in170.94 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.1 in2.5 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.18 in4.6 mm
a - Effective Center Location3 N/A -0.26 in-6.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 21200 lbf94300 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 81700 lbf364000 N

C0 - Static Radial Rating

 N/A 122000 lbf543000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 15100 lbf67100 N

Factors

K - Factor7 N/A 1.4
e - ISO Factor8 N/A 0.42
Y - ISO Factor9 N/A 1.44

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 269.2

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 49.5
Cg - Geometry Factor10 N/A 0.116
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.