Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 78000C

Cone Part Number

 N/A 78215C

Cup Part Number

 N/A 78537

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 78215C-902A1

Dimensions

d - Bore

 N/A 2.1250 in53.975 mm

D - Cup Outer Diameter

 N/A 5.3750 in136.525 mm

B - Cone Width

 N/A 1.3085 in33.236 mm

C - Cup Width

 N/A 0.9260 in23.520 mm

T - Bearing Width

 N/A 1.4375 in36.513 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 3.05 in77.5 mm

db - Cone Backface Backing Diameter

 N/A 3.31 in84 mm

Da - Cup Frontface Backing Diameter

 N/A 5.16 in131.06 mm

Db - Cup Backface Backing Diameter

 N/A 4.53 in115.06 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.21 in5.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.22 in5.6 mm
a - Effective Center Location3 N/A 0.33 in8.4 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 13800 lbf61300 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 53200 lbf237000 N

C0 - Static Radial Rating

 N/A 52600 lbf234000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 20400 lbf90900 N

Factors

K - Factor7 N/A 0.67
e - ISO Factor8 N/A 0.87
Y - ISO Factor9 N/A 0.69

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 71.3

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 17.6
Cg - Geometry Factor10 N/A 0.0926
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.