Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 84000

Cone Part Number

 N/A 84115

Cup Part Number

 N/A 84155

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 11 1/2 in292.100 mm

D - Cup Outer Diameter

 N/A 15.5 in393.7 mm

B - Cone Width

 N/A 2 in50.8 mm

C - Cup Width

 N/A 1.7500 in44.450 mm

T - Bearing Width

 N/A 2.5000 in63.500 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.560 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 12.17 in309 mm

db - Cone Backface Backing Diameter

 N/A 12.32 in313 mm

Da - Cup Frontface Backing Diameter

 N/A 14.89 in378.20 mm

Db - Cup Backface Backing Diameter

 N/A 14.29 in362.97 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.16 in4.1 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.51 in13 mm
a - Effective Center Location3 N/A 1.44 in36.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 31900 lbf142000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 123000 lbf548000 N

C0 - Static Radial Rating

 N/A 224000 lbf997000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 33300 lbf148000 N

Factors

K - Factor7 N/A 0.96
e - ISO Factor8 N/A 0.61
Y - ISO Factor9 N/A 0.98

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1230

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 302
Cg - Geometry Factor10 N/A 0.166
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.