Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 9100

Cone Part Number

 N/A 9185

Cup Part Number

 N/A 9121

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 2 11/16 in68.263 mm

D - Cup Outer Diameter

 N/A 6 in152.400 mm

B - Cone Width

 N/A 1.8125 in46.038 mm

C - Cup Width

 N/A 1.2500 in31.750 mm

T - Bearing Width

 N/A 1.8750 in47.625 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.560 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 3.2 in81.3 mm

db - Cone Backface Backing Diameter

 N/A 3.7 in94 mm

Da - Cup Frontface Backing Diameter

 N/A 5.75 in146.05 mm

Db - Cup Backface Backing Diameter

 N/A 5.12 in130.05 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.2 in5.1 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.28 in7.1 mm
a - Effective Center Location3 N/A -0.15 in-3.8 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 19700 lbf87700 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 76000 lbf338000 N

C0 - Static Radial Rating

 N/A 68700 lbf306000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 22100 lbf98500 N

Factors

K - Factor7 N/A 0.89
e - ISO Factor8 N/A 0.66
Y - ISO Factor9 N/A 0.91

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 87.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 13.7
Cg - Geometry Factor10 N/A 0.0912
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.