Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 96000

Cone Part Number

 N/A 96925

Cup Part Number

 N/A 96140

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 9.25 in234.95 mm

D - Cup Outer Diameter

 N/A 14 in355.6 mm

B - Cone Width

 N/A 2.6250 in66.675 mm

C - Cup Width

 N/A 1.8750 in47.625 mm

T - Bearing Width

 N/A 2.6875 in68.263 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.280 in7.100 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 10 in254 mm

db - Cone Backface Backing Diameter

 N/A 10.43 in265 mm

Da - Cup Frontface Backing Diameter

 N/A 13.16 in334.26 mm

Db - Cup Backface Backing Diameter

 N/A 12.52 in318.01 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.2 in5.1 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.43 in10.9 mm
a - Effective Center Location3 N/A 0.67 in17 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 44200 lbf197000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 171000 lbf759000 N

C0 - Static Radial Rating

 N/A 319000 lbf1420000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 44700 lbf199000 N

Factors

K - Factor7 N/A 0.99
e - ISO Factor8 N/A 0.59
Y - ISO Factor9 N/A 1.02

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1140

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 160
Cg - Geometry Factor10 N/A 0.163
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.