Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A A2000

Cone Part Number

 N/A A2047

Cup Part Number

 N/A A2127

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Note

 N/A This part has a non-standard shoulder design. Please email customer CAD for shoulder details to ensure the proper design of mating components.

Dimensions

d - Bore

 N/A 0.4719 in11.986 mm

D - Cup Outer Diameter

 N/A 1.2595 in31.991 mm

B - Cone Width

 N/A 0.4246 in10.785 mm

C - Cup Width

 N/A 0.3755 in9.538 mm

T - Bearing Width

 N/A 0.4161 in10.569 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.03 in0.800 mm
r - Cup Backface "To Clear" Radius2 N/A 0.050 in1.27 mm

da - Cone Frontface Backing Diameter

 N/A 0.61 in15.5 mm

db - Cone Backface Backing Diameter

 N/A 0.65 in16.5 mm

Da - Cup Frontface Backing Diameter

 N/A 1.14 in28.96 mm

Db - Cup Backface Backing Diameter

 N/A 1.02 in25.91 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.09 in2.3 mm

Aa - Cage-Cone Backface Clearance

 N/A -0.03 in-0.8 mm
a - Effective Center Location3 N/A -0.12 in-3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 630 lbf2800 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 2430 lbf10800 N

C0 - Static Radial Rating

 N/A 2070 lbf9230 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 437 lbf1940 N

Factors

K - Factor7 N/A 1.44
e - ISO Factor8 N/A 0.41
Y - ISO Factor9 N/A 1.48

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1.7

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 3.2
Cg - Geometry Factor10 N/A 0.0308
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.