Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A A4000

Cone Part Number

 N/A A4050

Cup Part Number

 N/A A4138

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A A4050-90012 A4050-90068

Dimensions

d - Bore

 N/A 1/2 in12.7 mm

D - Cup Outer Diameter

 N/A 1.3775 in34.989 mm

B - Cone Width

 N/A 0.4326 in10.988 mm

C - Cup Width

 N/A 0.3437 in8.730 mm

T - Bearing Width

 N/A 0.4330 in10.998 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.050 in1.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.050 in1.27 mm

da - Cone Frontface Backing Diameter

 N/A 0.67 in17 mm

db - Cone Backface Backing Diameter

 N/A 0.73 in18.5 mm

Da - Cup Frontface Backing Diameter

 N/A 1.28 in32.51 mm

Db - Cup Backface Backing Diameter

 N/A 1.14 in28.96 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.07 in1.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0 in0 mm
a - Effective Center Location3 N/A -0.1 in-2.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 767 lbf3410 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 2960 lbf13200 N

C0 - Static Radial Rating

 N/A 2580 lbf11500 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 594 lbf2640 N

Factors

K - Factor7 N/A 1.29
e - ISO Factor8 N/A 0.45
Y - ISO Factor9 N/A 1.32

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 2.3

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 4.12
Cg - Geometry Factor10 N/A 0.0355
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.