Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Cone Part Number

 N/A DX903631

Cup Part Number

 N/A DX417575

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 9.25 in234.95 mm

D - Cup Outer Diameter

 N/A 15.1250 in384.175 mm

B - Cone Width

 N/A 4.4375 in112.713 mm

C - Cup Width

 N/A 3.5625 in90.488 mm

T - Bearing Width

 N/A 4.4374 in112.710 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 10.2 in259 mm

db - Cone Backface Backing Diameter

 N/A 10.59 in269.0 mm

Da - Cup Frontface Backing Diameter

 N/A 14.32 in363.70 mm

Db - Cup Backface Backing Diameter

 N/A 13.62 in345.95 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.16 in4.1 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.37 in9.4 mm
a - Effective Center Location3 N/A -1.1 in-27.9 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 120000 lbf535000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 464000 lbf2060000 N

C0 - Static Radial Rating

 N/A 699000 lbf3110000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 68400 lbf304000 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1964.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 148.4
Cg - Geometry Factor10 N/A 0.164
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.