Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 108000

Cone Part Number

 N/A EE108065

Cup Part Number

 N/A 108142

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 6 1/2 in165.1 mm

D - Cup Outer Diameter

 N/A 14.2500 in361.950 mm

B - Cone Width

 N/A 4.1250 in104.775 mm

C - Cup Width

 N/A 3 in76.2 mm

T - Bearing Width

 N/A 4.1875 in106.363 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.530 in13.460 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 7.64 in194 mm

db - Cone Backface Backing Diameter

 N/A 8.46 in215 mm

Da - Cup Frontface Backing Diameter

 N/A 12.99 in329.90 mm

Db - Cup Backface Backing Diameter

 N/A 12.72 in323.09 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.26 in6.6 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.63 in16 mm
a - Effective Center Location3 N/A -1.29 in-32.8 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 84200 lbf375000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 325000 lbf1450000 N

C0 - Static Radial Rating

 N/A 439000 lbf1950000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 48300 lbf215000 N

Factors

K - Factor7 N/A 1.74
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.79

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 942

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 71.4
Cg - Geometry Factor10 N/A 0.127
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.