Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 114000

Cone Part Number

 N/A EE114080

Cup Part Number

 N/A 114160

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 8 in203.2 mm

D - Cup Outer Diameter

 N/A 16.0000 in406.400 mm

B - Cone Width

 N/A 3.3750 in85.725 mm

C - Cup Width

 N/A 2.2500 in57.150 mm

T - Bearing Width

 N/A 3.6250 in92.075 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 9.57 in243 mm

db - Cone Backface Backing Diameter

 N/A 10.71 in272 mm

Da - Cup Frontface Backing Diameter

 N/A 14.78 in375.41 mm

Db - Cup Backface Backing Diameter

 N/A 13.74 in349.00 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.44 in11.2 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.74 in18.8 mm
a - Effective Center Location3 N/A 0.98 in24.9 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 71000 lbf316000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 274000 lbf1220000 N

C0 - Static Radial Rating

 N/A 328000 lbf1460000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 97000 lbf431000 N

Factors

K - Factor7 N/A 0.73
e - ISO Factor8 N/A 0.8
Y - ISO Factor9 N/A 0.75

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 795

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 80.2
Cg - Geometry Factor10 N/A 0.157
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.