Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 126000

Cone Part Number

 N/A EE126098

Cup Part Number

 N/A 126150

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A EE126098-902A2

Dimensions

d - Bore

 N/A 9.8130 in249.250 mm

D - Cup Outer Diameter

 N/A 15.0000 in381.000 mm

B - Cone Width

 N/A 3.0000 in76.200 mm

C - Cup Width

 N/A 2.2500 in57.150 mm

T - Bearing Width

 N/A 3.1250 in79.375 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.190 in4.83 mm

da - Cone Frontface Backing Diameter

 N/A 10.59 in269 mm

db - Cone Backface Backing Diameter

 N/A 10.98 in279 mm

Da - Cup Frontface Backing Diameter

 N/A 14.25 in357.90 mm

Db - Cup Backface Backing Diameter

 N/A 13.50 in342.90 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.13 in3.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.49 in12.4 mm
a - Effective Center Location3 N/A 0.38 in9.7 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 52900 lbf235000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 204000 lbf907000 N

C0 - Static Radial Rating

 N/A 381000 lbf1690000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 46800 lbf208000 N

Factors

K - Factor7 N/A 1.13
e - ISO Factor8 N/A 0.52
Y - ISO Factor9 N/A 1.16

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1320

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 169
Cg - Geometry Factor10 N/A 0.164
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.