Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 128000

Cone Part Number

 N/A EE128102

Cup Part Number

 N/A 128160

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 10.2500 in260.350 mm

D - Cup Outer Diameter

 N/A 16.0000 in406.400 mm

B - Cone Width

 N/A 2.6643 in67.673 mm

C - Cup Width

 N/A 2.1250 in53.975 mm

T - Bearing Width

 N/A 2.7500 in69.850 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.13 in3.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 11.5 in292 mm

db - Cone Backface Backing Diameter

 N/A 11.34 in288 mm

Da - Cup Frontface Backing Diameter

 N/A 15.13 in384.30 mm

Db - Cup Backface Backing Diameter

 N/A 14.88 in377.95 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.12 in3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.2 in5.1 mm
a - Effective Center Location3 N/A 0.26 in6.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 53900 lbf240000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 208000 lbf924000 N

C0 - Static Radial Rating

 N/A 409000 lbf1820000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 35600 lbf158000 N

Factors

K - Factor7 N/A 1.51
e - ISO Factor8 N/A 0.39
Y - ISO Factor9 N/A 1.55

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1727.7

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 255.2
Cg - Geometry Factor10 N/A 0.163
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.