Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 157000

Cone Part Number

 N/A EE157337

Cup Part Number

 N/A 157430

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A EE157337-90010

Dimensions

d - Bore

 N/A 33.7500 in857.250 mm

D - Cup Outer Diameter

 N/A 43.0000 in1092.200 mm

B - Cone Width

 N/A 4.3750 in111.125 mm

C - Cup Width

 N/A 3 in76.2 mm

T - Bearing Width

 N/A 4.7500 in120.650 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.750 in19.050 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 35.2 in894 mm

db - Cone Backface Backing Diameter

 N/A 36.5 in927 mm

Da - Cup Frontface Backing Diameter

 N/A 42.15 in1070.61 mm

Db - Cup Backface Backing Diameter

 N/A 40.75 in1035.05 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.31 in7.9 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.8 in20.3 mm
a - Effective Center Location3 N/A 4.43 in112.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 169000 lbf754000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 654000 lbf2910000 N

C0 - Static Radial Rating

 N/A 1710000 lbf7630000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 162000 lbf719000 N

Factors

K - Factor7 N/A 1.05
e - ISO Factor8 N/A 0.56
Y - ISO Factor9 N/A 1.08

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 16100

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 1534.4
Cg - Geometry Factor10 N/A 0.377
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.