Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 158000

Cone Part Number

 N/A EE158350

Cup Part Number

 N/A 158442

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A EE158350-90011

Dimensions

d - Bore

 N/A 35.0000 in889.000 mm

D - Cup Outer Diameter

 N/A 44.2500 in1123.950 mm

B - Cone Width

 N/A 4.3750 in111.125 mm

C - Cup Width

 N/A 3 in76.2 mm

T - Bearing Width

 N/A 4.7500 in120.650 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.750 in19.050 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 36.5 in927 mm

db - Cone Backface Backing Diameter

 N/A 37.68 in957 mm

Da - Cup Frontface Backing Diameter

 N/A 42.91 in1089.91 mm

Db - Cup Backface Backing Diameter

 N/A 41.73 in1059.94 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.32 in8.13 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.81 in20.57 mm
a - Effective Center Location3 N/A 4.89 in124.2 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 170000 lbf756000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 655000 lbf2920000 N

C0 - Static Radial Rating

 N/A 1740000 lbf7740000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 167000 lbf745000 N

Factors

K - Factor7 N/A 1.01
e - ISO Factor8 N/A 0.58
Y - ISO Factor9 N/A 1.04

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 16994.2

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 1630.2
Cg - Geometry Factor10 N/A 0.387
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.