Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 160000

Cone Part Number

 N/A EE161300

Cup Part Number

 N/A 161925

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 13.0000 in330.200 mm

D - Cup Outer Diameter

 N/A 19.2500 in488.950 mm

B - Cone Width

 N/A 2.1875 in55.563 mm

C - Cup Width

 N/A 1.5000 in38.100 mm

T - Bearing Width

 N/A 2.3750 in60.325 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.280 in7.100 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 14.02 in356 mm

db - Cone Backface Backing Diameter

 N/A 14.45 in367 mm

Da - Cup Frontface Backing Diameter

 N/A 17.95 in455.90 mm

Db - Cup Backface Backing Diameter

 N/A 17.83 in452.88 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.22 in5.6 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.51 in13 mm
a - Effective Center Location3 N/A 1.33 in33.8 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 36600 lbf163000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 141000 lbf628000 N

C0 - Static Radial Rating

 N/A 250000 lbf1110000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 31400 lbf140000 N

Factors

K - Factor7 N/A 1.17
e - ISO Factor8 N/A 0.5
Y - ISO Factor9 N/A 1.2

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1730.8

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 299.6
Cg - Geometry Factor10 N/A 0.174
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.