Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 200000

Cone Part Number

 N/A EE201250

Cup Part Number

 N/A 201800

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 12.5000 in317.500 mm

D - Cup Outer Diameter

 N/A 18 in457.2 mm

B - Cone Width

 N/A 2.5625 in65.088 mm

C - Cup Width

 N/A 1.6875 in42.863 mm

T - Bearing Width

 N/A 2.6250 in66.675 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.270 in6.860 mm
r - Cup Backface "To Clear" Radius2 N/A 0.270 in6.86 mm

da - Cone Frontface Backing Diameter

 N/A 13.27 in337 mm

db - Cone Backface Backing Diameter

 N/A 13.7 in348 mm

Da - Cup Frontface Backing Diameter

 N/A 16.93 in430.00 mm

Db - Cup Backface Backing Diameter

 N/A 16.69 in423.93 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.23 in5.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.55 in14 mm
a - Effective Center Location3 N/A 0.38 in9.7 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 58000 lbf258000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 224000 lbf996000 N

C0 - Static Radial Rating

 N/A 373000 lbf1660000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 38900 lbf173000 N

Factors

K - Factor7 N/A 1.49
e - ISO Factor8 N/A 0.39
Y - ISO Factor9 N/A 1.53

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1880.1

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 284.2
Cg - Geometry Factor10 N/A 0.167
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.