Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 217000

Cone Part Number

 N/A EE217064

Cup Part Number

 N/A 217112W

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 5.7500 in146.050 mm

D - Cup Outer Diameter

 N/A 11.25 in285.750 mm

B - Cone Width

 N/A 2.875 in73.025 mm

C - Cup Width

 N/A 2.1875 in55.563 mm

T - Bearing Width

 N/A 3.0001 in76.203 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.050 in1.270 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 6.54 in166.1 mm

db - Cone Backface Backing Diameter

 N/A 6.54 in166.1 mm

Da - Cup Frontface Backing Diameter

 N/A 10.30 in261.60 mm

Db - Cup Backface Backing Diameter

 N/A 9.88 in250.95 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.11 in2.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.57 in14.5 mm
a - Effective Center Location3 N/A -0.59 in-15 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 41700 lbf185000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 161000 lbf715000 N

C0 - Static Radial Rating

 N/A 237000 lbf1060000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 28700 lbf128000 N

Factors

K - Factor7 N/A 1.45
e - ISO Factor8 N/A 0.4
Y - ISO Factor9 N/A 1.49

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 556.3

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 71.8
Cg - Geometry Factor10 N/A 0.114
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.