Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 222000

Cone Part Number

 N/A EE222070

Cup Part Number

 N/A 222126

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 7 in177.800 mm

D - Cup Outer Diameter

 N/A 12.5970 in319.964 mm

B - Cone Width

 N/A 3.3750 in85.725 mm

C - Cup Width

 N/A 2.5625 in65.088 mm

T - Bearing Width

 N/A 3.5001 in88.903 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 N/A 0.190 in4.83 mm

da - Cone Frontface Backing Diameter

 N/A 7.87 in200 mm

db - Cone Backface Backing Diameter

 N/A 8.03 in204 mm

Da - Cup Frontface Backing Diameter

 N/A 11.75 in298.50 mm

Db - Cup Backface Backing Diameter

 N/A 11.34 in288.04 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.12 in3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.56 in14.2 mm
a - Effective Center Location3 N/A -0.65 in-16.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 55600 lbf247000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 215000 lbf954000 N

C0 - Static Radial Rating

 N/A 361000 lbf1600000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 38100 lbf169000 N

Factors

K - Factor7 N/A 1.46
e - ISO Factor8 N/A 0.4
Y - ISO Factor9 N/A 1.5

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 947.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 104.7
Cg - Geometry Factor10 N/A 0.136
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.