Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 234000

Cone Part Number

 N/A EE234160

Cup Part Number

 N/A 234215W

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 16.0000 in406.400 mm

D - Cup Outer Diameter

 N/A 21.5000 in546.1 mm

B - Cone Width

 N/A 2.4063 in61.120 mm

C - Cup Width

 N/A 2.1875 in55.563 mm

T - Bearing Width

 N/A 3.0001 in76.203 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 16.73 in425 mm

db - Cone Backface Backing Diameter

 N/A 17.13 in435 mm

Da - Cup Frontface Backing Diameter

 N/A 20.31 in515.87 mm

Db - Cup Backface Backing Diameter

 N/A 19.84 in503.94 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.31 in7.9 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.5 in12.7 mm
a - Effective Center Location3 N/A 1.4 in35.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 63300 lbf282000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 244000 lbf1090000 N

C0 - Static Radial Rating

 N/A 451000 lbf2010000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 51600 lbf230000 N

Factors

K - Factor7 N/A 1.23
e - ISO Factor8 N/A 0.48
Y - ISO Factor9 N/A 1.26

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 2780

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 448
Cg - Geometry Factor10 N/A 0.202
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.