Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 240000

Cone Part Number

 N/A EE241693

Cup Part Number

 N/A 242375

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A EE241693-90017

Dimensions

d - Bore

 N/A 16.9375 in430.213 mm

D - Cup Outer Diameter

 N/A 23.7500 in603.25 mm

B - Cone Width

 N/A 2.875 in73.025 mm

C - Cup Width

 N/A 2.0000 in50.800 mm

T - Bearing Width

 N/A 3.0000 in76.200 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 17.91 in455 mm

db - Cone Backface Backing Diameter

 N/A 18.31 in465 mm

Da - Cup Frontface Backing Diameter

 N/A 22.17 in563.10 mm

Db - Cup Backface Backing Diameter

 N/A 21.97 in558.04 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.02 in0.5 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.69 in17.5 mm
a - Effective Center Location3 N/A 1.85 in47 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 65700 lbf292000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 253000 lbf1130000 N

C0 - Static Radial Rating

 N/A 491000 lbf2190000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 59000 lbf262000 N

Factors

K - Factor7 N/A 1.11
e - ISO Factor8 N/A 0.52
Y - ISO Factor9 N/A 1.14

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 3350

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 551
Cg - Geometry Factor10 N/A 0.221
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.