Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 244000

Cone Part Number

 N/A EE244180

Cup Part Number

 N/A 244235

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A EE244180-90040 EE244180-90044

Dimensions

d - Bore

 N/A 18.0000 in457.200 mm

D - Cup Outer Diameter

 N/A 23.5000 in596.9 mm

B - Cone Width

 N/A 2.875 in73.025 mm

C - Cup Width

 N/A 2.1250 in53.975 mm

T - Bearing Width

 N/A 3.0000 in76.200 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.380 in9.700 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 18.82 in478 mm

db - Cone Backface Backing Diameter

 N/A 19.45 in494 mm

Da - Cup Frontface Backing Diameter

 N/A 22.48 in570.99 mm

Db - Cup Backface Backing Diameter

 N/A 22.32 in566.93 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.24 in6.1 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.49 in12.4 mm
a - Effective Center Location3 N/A 1.05 in26.7 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 82400 lbf367000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 318000 lbf1410000 N

C0 - Static Radial Rating

 N/A 649000 lbf2890000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 57100 lbf254000 N

Factors

K - Factor7 N/A 1.44
e - ISO Factor8 N/A 0.4
Y - ISO Factor9 N/A 1.48

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 4410

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 627
Cg - Geometry Factor10 N/A 0.223
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.