Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 290000

Cone Part Number

 N/A EE291175

Cup Part Number

 N/A 291750

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 11.7500 in298.450 mm

D - Cup Outer Diameter

 N/A 17.5 in444.5 mm

B - Cone Width

 N/A 2.4375 in61.913 mm

C - Cup Width

 N/A 1.5625 in39.688 mm

T - Bearing Width

 N/A 2.5000 in63.500 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.310 in7.900 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

 N/A 12.6 in320 mm

db - Cone Backface Backing Diameter

 N/A 13.07 in332 mm

Da - Cup Frontface Backing Diameter

 N/A 16.63 in422.40 mm

Db - Cup Backface Backing Diameter

 N/A 16.38 in416.05 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.34 in8.6 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.4 in10.2 mm
a - Effective Center Location3 N/A 0.3 in7.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 51700 lbf230000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 199000 lbf887000 N

C0 - Static Radial Rating

 N/A 312000 lbf1390000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 33400 lbf149000 N

Factors

K - Factor7 N/A 1.55
e - ISO Factor8 N/A 0.38
Y - ISO Factor9 N/A 1.59

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1580

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 245
Cg - Geometry Factor10 N/A 0.156
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.