Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 299000

Cone Part Number

 N/A EE299615

Cup Part Number

 N/A 299711

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A EE299615-90013

Dimensions

d - Bore

 N/A 61.5000 in1562.100 mm

D - Cup Outer Diameter

 N/A 71.1250 in1806.575 mm

B - Cone Width

 N/A 4.8750 in123.825 mm

C - Cup Width

 N/A 3.3750 in85.725 mm

T - Bearing Width

 N/A 5.0000 in127 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.380 in9.650 mm
r - Cup Backface "To Clear" Radius2 N/A 0.380 in9.65 mm

da - Cone Frontface Backing Diameter

 N/A 62.99 in1600 mm

db - Cone Backface Backing Diameter

 N/A 63.58 in1615 mm

Da - Cup Frontface Backing Diameter

 N/A 71.46 in1815.08 mm

Db - Cup Backface Backing Diameter

 N/A 66.93 in1700.02 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.49 in12.4 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.64 in16.3 mm
a - Effective Center Location3 N/A 7.5 in190.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 265000 lbf1180000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 1020000 lbf4540000 N

C0 - Static Radial Rating

 N/A 3770000 lbf16800000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 215000 lbf955000 N

Factors

K - Factor7 N/A 1.23
e - ISO Factor8 N/A 0.47
Y - ISO Factor9 N/A 1.27

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 69875.1

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 7454.3
Cg - Geometry Factor10 N/A 0.575
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.