Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 321000

Cone Part Number

 N/A EE321145

Cup Part Number

 N/A 321240

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A EE321145-90018

Dimensions

d - Bore

 N/A 14.5000 in368.3 mm

D - Cup Outer Diameter

 N/A 24.0 in609.600 mm

B - Cone Width

 N/A 5.5000 in139.700 mm

C - Cup Width

 N/A 4.375 in111.125 mm

T - Bearing Width

 N/A 5.6250 in142.875 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.310 in7.870 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 15.91 in404 mm

db - Cone Backface Backing Diameter

 N/A 16.26 in413 mm

Da - Cup Frontface Backing Diameter

 N/A 22.56 in573.00 mm

Db - Cup Backface Backing Diameter

 N/A 21.85 in554.99 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.25 in6.35 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.78 in19.81 mm
a - Effective Center Location3 N/A -0.93 in-23.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 173000 lbf770000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 668000 lbf2970000 N

C0 - Static Radial Rating

 N/A 1210000 lbf5380000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 106000 lbf470000 N

Factors

K - Factor7 N/A 1.64
e - ISO Factor8 N/A 0.36
Y - ISO Factor9 N/A 1.68

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 4401.5

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 304.6
Cg - Geometry Factor10 N/A 0.217
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.