Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 328000

Cone Part Number

 N/A EE328167

Cup Part Number

 N/A 328269

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A EE328167-90020

Dimensions

d - Bore

 N/A 16.7500 in425.450 mm

D - Cup Outer Diameter

 N/A 26.9960 in685.698 mm

B - Cone Width

 N/A 5.6220 in142.799 mm

C - Cup Width

 N/A 4.1250 in104.775 mm

T - Bearing Width

 N/A 5.6250 in142.875 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.500 in12.700 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 18.23 in463 mm

db - Cone Backface Backing Diameter

 N/A 18.98 in482 mm

Da - Cup Frontface Backing Diameter

 N/A 25.07 in636.80 mm

Db - Cup Backface Backing Diameter

 N/A 24.57 in624.08 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.17 in4.3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.8 in20.3 mm
a - Effective Center Location3 N/A -0.32 in-8.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 183000 lbf812000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 704000 lbf3130000 N

C0 - Static Radial Rating

 N/A 1360000 lbf6030000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 126000 lbf559000 N

Factors

K - Factor7 N/A 1.45
e - ISO Factor8 N/A 0.4
Y - ISO Factor9 N/A 1.49

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 5606.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 353
Cg - Geometry Factor10 N/A 0.244
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.