Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 538000

Cone Part Number

 N/A EE538261

Cup Part Number

 N/A 538370

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 26.0000 in660.400 mm

D - Cup Outer Diameter

 N/A 37.0000 in939.800 mm

B - Cone Width

 N/A 5.0000 in127.000 mm

C - Cup Width

 N/A 3.8750 in98.425 mm

T - Bearing Width

 N/A 5.3751 in136.528 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.35 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 27.4 in696 mm

db - Cone Backface Backing Diameter

 N/A 27.87 in708 mm

Da - Cup Frontface Backing Diameter

 N/A 35.02 in889.50 mm

Db - Cup Backface Backing Diameter

 N/A 34.49 in876.05 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.41 in10.4 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.79 in20.1 mm
a - Effective Center Location3 N/A 1.21 in30.7 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 207000 lbf923000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 800000 lbf3560000 N

C0 - Static Radial Rating

 N/A 1750000 lbf7800000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 144000 lbf642000 N

Factors

K - Factor7 N/A 1.44
e - ISO Factor8 N/A 0.41
Y - ISO Factor9 N/A 1.48

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 11455.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 802.1
Cg - Geometry Factor10 N/A 0.308
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.