Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 560000

Cone Part Number

 N/A EE560629

Cup Part Number

 N/A 561279

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 6.2960 in159.918 mm

D - Cup Outer Diameter

 N/A 12.75 in323.85 mm

B - Cone Width

 N/A 3.0000 in76.200 mm

C - Cup Width

 N/A 2.1250 in53.975 mm

T - Bearing Width

 N/A 3.0626 in77.790 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.410 in10.400 mm
r - Cup Backface "To Clear" Radius2 N/A 0.190 in4.83 mm

da - Cone Frontface Backing Diameter

 N/A 7.24 in184 mm

db - Cone Backface Backing Diameter

 N/A 7.95 in202 mm

Da - Cup Frontface Backing Diameter

 N/A 11.36 in288.50 mm

Db - Cup Backface Backing Diameter

 N/A 11.10 in281.94 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.19 in4.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.5 in12.7 mm
a - Effective Center Location3 N/A -0.32 in-8.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 60700 lbf270000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 234000 lbf1040000 N

C0 - Static Radial Rating

 N/A 295000 lbf1310000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 48200 lbf214000 N

Factors

K - Factor7 N/A 1.26
e - ISO Factor8 N/A 0.46
Y - ISO Factor9 N/A 1.29

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 659.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 77.8
Cg - Geometry Factor10 N/A 0.126
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.