Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 590000

Cone Part Number

 N/A EE590650

Cup Part Number

 N/A 591350

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 6 1/2 in165.1 mm

D - Cup Outer Diameter

 N/A 13-1/2 in342.900 mm

B - Cone Width

 N/A 3.1875 in80.963 mm

C - Cup Width

 N/A 2.1250 in53.975 mm

T - Bearing Width

 N/A 3.1250 in79.375 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.690 in17.530 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 7.52 in191 mm

db - Cone Backface Backing Diameter

 N/A 8.78 in223 mm

Da - Cup Frontface Backing Diameter

 N/A 12.12 in307.85 mm

Db - Cup Backface Backing Diameter

 N/A 11.73 in297.94 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.14 in3.6 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.52 in13.2 mm
a - Effective Center Location3 N/A -0.18 in-4.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 55600 lbf248000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 215000 lbf955000 N

C0 - Static Radial Rating

 N/A 266000 lbf1180000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 47300 lbf210000 N

Factors

K - Factor7 N/A 1.18
e - ISO Factor8 N/A 0.5
Y - ISO Factor9 N/A 1.21

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 671.9

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 92.9
Cg - Geometry Factor10 N/A 0.129
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.