Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 650000

Cone Part Number

 N/A EE650170

Cup Part Number

 N/A 650270

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A EE650170-90016

Dimensions

d - Bore

 N/A 17.0040 in431.902 mm

D - Cup Outer Diameter

 N/A 26.9960 in685.698 mm

B - Cone Width

 N/A 6.8750 in174.625 mm

C - Cup Width

 N/A 5.6250 in142.875 mm

T - Bearing Width

 N/A 7.0000 in177.800 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 18.54 in471 mm

db - Cone Backface Backing Diameter

 N/A 18.78 in477 mm

Da - Cup Frontface Backing Diameter

 N/A 25.63 in648.50 mm

Db - Cup Backface Backing Diameter

 N/A 24.69 in627.13 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.29 in7.4 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.5 in12.7 mm
a - Effective Center Location3 N/A -1.43 in-36.3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 270000 lbf1200000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 1040000 lbf4640000 N

C0 - Static Radial Rating

 N/A 2080000 lbf9230000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 150000 lbf669000 N

Factors

K - Factor7 N/A 1.8
e - ISO Factor8 N/A 0.32
Y - ISO Factor9 N/A 1.85

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 7670

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 341
Cg - Geometry Factor10 N/A 0.254
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.