Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 670000

Cone Part Number

 N/A EE671801

Cup Part Number

 N/A 672873

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Related Assembly Number(s)

 N/A EE671801-90016 EE671801-90025

Dimensions

d - Bore

 N/A 18.0000 in457.200 mm

D - Cup Outer Diameter

 N/A 28.7460 in730.148 mm

B - Cone Width

 N/A 4.5000 in114.300 mm

C - Cup Width

 N/A 3.25 in82.55 mm

T - Bearing Width

 N/A 4.7500 in120.650 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.380 in9.700 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 19.33 in491 mm

db - Cone Backface Backing Diameter

 N/A 19.96 in507 mm

Da - Cup Frontface Backing Diameter

 N/A 26.93 in680.50 mm

Db - Cup Backface Backing Diameter

 N/A 26.57 in674.88 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.54 in13.7 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.71 in18 mm
a - Effective Center Location3 N/A 0.21 in5.3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 165000 lbf733000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 635000 lbf2830000 N

C0 - Static Radial Rating

 N/A 1100000 lbf4870000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 111000 lbf492000 N

Factors

K - Factor7 N/A 1.49
e - ISO Factor8 N/A 0.39
Y - ISO Factor9 N/A 1.53

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 4970

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 343
Cg - Geometry Factor10 N/A 0.231
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.