Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 722000

Cone Part Number

 N/A EE722115

Cup Part Number

 N/A 722185

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 11 1/2 in292.100 mm

D - Cup Outer Diameter

 N/A 18.5000 in469.900 mm

B - Cone Width

 N/A 3.6875 in93.663 mm

C - Cup Width

 N/A 2.75 in69.85 mm

T - Bearing Width

 N/A 3.7500 in95.250 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.380 in9.700 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 12.76 in324 mm

db - Cone Backface Backing Diameter

 N/A 12.99 in330.0 mm

Da - Cup Frontface Backing Diameter

 N/A 17.05 in433.07 mm

Db - Cup Backface Backing Diameter

 N/A 16.93 in430.02 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.08 in2 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.62 in15.7 mm
a - Effective Center Location3 N/A -0.3 in-7.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 94000 lbf418000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 363000 lbf1610000 N

C0 - Static Radial Rating

 N/A 527000 lbf2350000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 60800 lbf271000 N

Factors

K - Factor7 N/A 1.55
e - ISO Factor8 N/A 0.38
Y - ISO Factor9 N/A 1.59

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1890

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 143
Cg - Geometry Factor10 N/A 0.167
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.