Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 980000

Cone Part Number

 N/A EE982028

Cup Part Number

 N/A 982900

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 20.2500 in514.350 mm

D - Cup Outer Diameter

 N/A 29.0000 in736.600 mm

B - Cone Width

 N/A 3.2188 in81.758 mm

C - Cup Width

 N/A 2.1250 in53.975 mm

T - Bearing Width

 N/A 3.5000 in88.900 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 21.61 in549 mm

db - Cone Backface Backing Diameter

 N/A 21.85 in555 mm

Da - Cup Frontface Backing Diameter

 N/A 27.60 in701.04 mm

Db - Cup Backface Backing Diameter

 N/A 27.28 in692.91 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.41 in10.4 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.69 in17.5 mm
a - Effective Center Location3 N/A 1.79 in45.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 116000 lbf516000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 447000 lbf1990000 N

C0 - Static Radial Rating

 N/A 772000 lbf3430000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 94000 lbf418000 N

Factors

K - Factor7 N/A 1.23
e - ISO Factor8 N/A 0.47
Y - ISO Factor9 N/A 1.27

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 4901.2

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 606.3
Cg - Geometry Factor10 N/A 0.243
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.