Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A H242600

Cone Part Number

 N/A H242649

Cup Part Number

 N/A H242610

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 8.1250 in206.375 mm

D - Cup Outer Diameter

 N/A 13.2500 in336.550 mm

B - Cone Width

 N/A 3.9375 in100.013 mm

C - Cup Width

 N/A 3.0625 in77.788 mm

T - Bearing Width

 N/A 3.8750 in98.425 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.13 in3.300 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 8.94 in227 mm

db - Cone Backface Backing Diameter

 N/A 9.09 in231 mm

Da - Cup Frontface Backing Diameter

 N/A 12.52 in317.80 mm

Db - Cup Backface Backing Diameter

 N/A 12.05 in306.07 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.12 in3 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.41 in10.4 mm
a - Effective Center Location3 N/A -1 in-25.4 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 79000 lbf351000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 305000 lbf1350000 N

C0 - Static Radial Rating

 N/A 522000 lbf2320000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 45000 lbf200000 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1404.1

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 134.8
Cg - Geometry Factor10 N/A 0.147
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.