Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A H247500

Cone Part Number

 N/A H247548

Cup Part Number

 N/A H247510

Design Unit

 N/A Inch

Cage Material

 N/A Pin-Type

Dimensions

d - Bore

 N/A 9.25 in234.95 mm

D - Cup Outer Diameter

 N/A 15.1250 in384.175 mm

B - Cone Width

 N/A 4.4375 in112.713 mm

C - Cup Width

 N/A 3.5625 in90.488 mm

T - Bearing Width

 N/A 4.4375 in112.713 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.25 in6.4 mm
r - Cup Backface "To Clear" Radius2 N/A 0.250 in6.35 mm

da - Cone Frontface Backing Diameter

 N/A 10.2 in259 mm

db - Cone Backface Backing Diameter

 N/A 10.59 in269.0 mm

Da - Cup Frontface Backing Diameter

 N/A 14.32 in363.70 mm

Db - Cup Backface Backing Diameter

 N/A 13.62 in345.95 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.22 in5.6 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.27 in6.9 mm
a - Effective Center Location3 N/A -1.1 in-27.9 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 109000 lbf486000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 422000 lbf1880000 N

C0 - Static Radial Rating

 N/A 757000 lbf3370000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 62200 lbf277000 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 2080

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 156
Cg - Geometry Factor10 N/A 0.167
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.